DETERMINATION OF OPTIMUM PARAMETERS FOR THE DESIGN OF COMPOSITE SHAFT
DOI:
https://doi.org/10.55766/sujst-2024-02-e02719Keywords:
Composite material, Critical speed, Damping, Dynamic propertiesAbstract
In this research work, emphasis is given to investigate the dynamic properties of a revolving composite shaft. The experimental analysis is used to calculate the Eigen pairs for different modes of vibration of revolving shafts. A Finite Element Method (FEM) prototype is used to articulate the stiffness matrices. The stiffness matrices consider the property of distortion about an axis, the shear distortion on the Eigen trend of the revolving shaft. The perilous speed of the revolving shaft is calculated based on the Campbell diagram. It also helps to identify the volatility areas to attain accuracy and regulate the dynamic performance of the physical system in a resonance state. The effect of laminate constraints like piling orders, fiber direction, boundary conditions, and percentage of fiber volume on the natural rate of recurrence and perilous speed of the shaft is investigated. The results obtained by mathematical analysis and by performing experiments were compared. It is observed that the results obtained by the FEM method and experimental results for the composites shaft are in good agreement with each other.
References
Alberto D’A. and Luigi G. (2019). Principal Features of Fatigue and Residual Strength of Composite Materials Subjected to Constant Amplitude (CA) Loading. Material, 12(16): 2,586. https://doi.org/10.3390/ma12162586
Boukhalfa, A., Hadjoui, A. and Hamza Cherif, S.M. (2008). Free Vibration Analysis of a Rotating Composite Shaft Using the 𝑝-Version of the Finite Element Method. International Journal of Rotating Machinery, 1-10. https://doi.org/10.1155/2008/752062
Charles W.B. (2012). Manual on Experimental Methods for Mechanical Testing of Composites. In Springer, Dordrecht, p.1-4
Chen, F., Liu, L., Lan, X., Li, Q., Leng, J., and Liu, Y. (2018). The study on the morphing composite propeller for marine vehicle. Part I: Design and numerical analysis. Composite Structures, 168:746-757. https://doi.org/10.1016/j.compstruct.2017.02.072
Chun-Do, K. and Charles. W.B. (1993). Critical speed analysis of laminated composite, hollow drive shafts. Composites Engineering, 3(7-8):633-643. https://doi.org/10.1016/0961-9526(93)90087-Z
Dipen, K.R., Durgesh, D.P., Emanoil, L.M. and Emanoil, L. (2019). Fiber-Reinforced Polymer Composites: Manufacturing, Properties, and Applications. Polymers Journal, 11(10):1,667. https://doi.org/10.3390/polym11101667
Dos Reis HLM, Goldman RB, Verstrate PH. (1987) Thin-walled laminated composite cylindrical tubes: part III - critical speed analysis. Journal of Composites Technology and Research; 9(2): 58-62 https://doi.org/10.1520/CTR10430J
Harry V., Bermingham, M., Dunn, M. and Veidt M. (2021). Layup optimization of laminated composite tubular structures under thermomechanical loading conditions using PSO Composite Structures, 276(2021):114483. https://doi.org/10.1016/j.compstruct.2021.114483
Gupta, K. and Singh, S.E. (1996) Dynamics of composite rotors. International Journal of Rotating Machinery, 2(3):179-186. https://doi.org/10.1155/2008/752062
Venkateshan, K., Ramanathan, K., Vijayanandh, R., Selvarajand, S., Kumar, G.R., and Kumar, M.S. (2020). Comparative structural analysis of advanced multi-layer composite materials. Materials Today Proceedings, 27(3):2,673-2,687 https://doi.org/10.1016/j.matpr.2019.11.247
Hajianmaleki, M. and Mohammad S.Q. (2013) Vibrations of straight and curved composite beams: A review. Composite Structures, 100:218-232, https://doi.org/10.1016/j.compstruct.2013.01.001
Meng, Y.S. Yan, L., Huang, W., Zhang, T.T., Du, Z.B. (2018). Structural design and analysis of a composite wing with high aspect ratio. Journal of Zhejiang University-SCIENCE A, 20:781-793. https://doi.org/10.1631/jzus.A1900271
Chang M.-Y., Chen, J.-K. and Chang, Y.C. (2004). A simple spinning laminated composite shaft model. International Journal of Solids and Structures, 41(3-4):637-662. https://doi.org/10.1016/j.ijsolstr.2003.09.043
Jeppesen, N., Mikkelsen, L.P., Dahl, V.A., Christensen, A.N. and Dahl, V.A. (2021). Quantifying effects of manufacturing methods on fiber orientation in unidirectional composites using structure tensor analysis. Composites Part A: Applied Science and Manufacturing, 149:106541. https://doi.org/10.1016/j.compositesa.2021.106541
Patel, A., kaneria, A.J., Sharma, D.S. and Trivedi, R. (2020). Dynamic analysis of micro-cantilever with electrostatic Force. Australian Journal of Mechanical Engineering, 20(3):1448-4846. https://doi.org/10.1080/14484846.2020.1761006
Müzel, S.D. Bonhin, E.P., Guimarães, N.M. and Guidi, E.S. (2020). Application of the Finite Element Method in the Analysis of Composite Materials: A Review. Polymers Journal, 12(4):818. https://doi.org/10.3390/polym12040818
Sino, R., Baranger, T.N., Chatelet, E. and Jacquet, G. (2008). Dynamic analysis of a rotating composite shaft. Composites Science and Technology, 68(2):337-345. https://doi.org/10.1016/j.compscitech.2007.06.019
You, Y.-J.; Jay Kim, J.-H., Park, K.-T. Seo, D.-W. and Lee, T.H. (2017). Modification of Rule of Mixtures for Tensile Strength. International Journal of Polymers, MDPI publication. 9(12):682-694. https://doi.org/10.3390/polym9120682
Zinberg H., Symonds M., and Corp, W. (1970). The Development of an Advanced Composite Tail Rotor Driveshaft. Engineering material science, 15.
