MECHANO-CHEMICALFABRICATIONOF NON-FIRING CERAMIC

Authors

  • Apiluck Eiad-ua College of Nanotechnology, King Mongkut’s Institute of Technology Ladkrabang, 1 Soi Chalongkrung 1, Ladkrabang, Bangkok 10520, Thailand.
  • Jiti Nukaew College of Nanotechnology, King Mongkut’s Institute of Technology Ladkrabang, 1 Soi Chalongkrung 1, Ladkrabang, Bangkok 10520, Thailand.
  • Takashi Shirai Ceramics Research Laboratory, Nagoya Institute of Technology, 3-101-1, Honmachi, Tajimi, Gifu 507-0033, Japan.
  • Masayoshi Fuji Ceramics Research Laboratory, Nagoya Institute of Technology, 3-101-1, Honmachi, Tajimi, Gifu 507-0033, Japan.

Keywords:

Non-firing ceramic, novel route, mechano-chemical, solidification

Abstract

Novelroute for non-firing ceramic was successfully fabricated in this paper. This study is particularly taking advantage of mechanochemically assisted chemical solidification for improving mechanical strength of ceramic green body. This method allows the surface activation of powder and control of the properties of powder not only by varying mechano-chemical treatment but also by managing the chemical solidification by alkaline binding. After drying at 25oC for 3 days, the ceramic green body (non-firing ceramic) was obtained. The results revealed that mechano-chemicaltreatment has a certain effect on the total bonding (Potassium ananate, KAlH4) and mechanical strength of non-firing ceramic. An increase in total number bond and high strength was obtained with milling time of mechano-chemical process.

References

Agnew, S.F. and Schoonover, J.R. (1996). Microstructrual Properties of High Level Waste Concentrates and Gels with raman and Infrared Spectrocopies. DOE Environmental Management Science Program (EMSP).

Ares, J.R., Aguey-Zinsou, K-F., Leardini, F., Ferrer, I.J., Fernandez, J-F., Guo, Z-X., and Sanchez, C. (2009). Hydrogen Absorption/Desorption Mechanism in Potassium Alanate (KAlH4) and Enhancement by TiCl3 Doping. J. Phys. Chem.C., 113:6845-6851.

Assih, T., Ayral, A., Abenoza, M., and Phalippou, J. (1998). Raman study of alumina gels. J. Mater. Sci., 23:3326-3331.

Balema, V.P., Pecharsky, V.K., and Dennis, K.W. (2000). Solid state phase transformation in LiAlH4 during high-energy ball-milling. J. Allo. Com., 313:69-74.

Delogu, F. and Cocco, G. (2003). Compositional effects on the mechanochemical synthesis of Fe-Ti and Cu-Ti amorphous alloys by mechanical alloying. J. Allo. Com., 352:92-98.

Delogu, F., Orru, R., and Cao, G. (2003). Anovel macrokinetic approach for mechanochemical reactions. Chem. Eng. Sci., 58:815-821.

Eiad-ua, A.,Shirai, T.,Kato, T., Orito, K., Watanabe, H., Fuji M., and Takahashi, M. (2010). Novel fabrication route for porous ceramics using waste materials by non-firing process. J. Cer. Soc. Jap., 118:745-748.

Eiad-ua, A.,Shirai, T., Watanabe, H., Fuji, M., Orito K., and Takahashi, M. (2010). Fabrication of non-firing ceramics assisted by particle surface activation using a planetary ball mill. Ceram. Trans., 219:129-135.

Eroglu, H., Ucuncu, O., and Acar, H.H. (2007). The effect of dry sludge addition supplied from pulp mill on the compressive strength cement. J. Uni. Chem. Tech. Met., 42(2):169-174.

Fletcher, R.A.,MacKenzie, K.J.D., Nicholson, C.L., and Shimada, S. (2005). The composition range of aluminosilicategeopolymers. J. Eur. Ceram. Soc., 25:1471-1477.

Hsing, H-I.and Yen, F-S. (2003). Effects of mechanical treatment on phase transformation and sintering of nano-sized γ-Fe2O3 powder.Cer. Int., 29:1-6.

Jantunen, H., Rautioaho, R., Leppavuori, S., and Uusimaki, A. (2000). Preparing low loss LTCC material without glass addition. J. Eur. Ceram. Soc., 83:2855-2857.

Lee, W.K.W. and van Deventer, J.S.H. (2007). Chemical interactions between siliceous aggregates and low-Ca alkali-activated cements. Cem. Con. Res., 37:844-855.

Meinshausen, M., Meinshausen, N., Hare, W., Raper, S.C.B., Frieler, K., Knutti, R., Frame, D.J. and Allen, M.R.(2009). Greenhouse-gas emission targets for limiting global warming to 2oC. Nature., 458(7242):1158-1162.

Perera, D.S., Cashion, J.D., Blackford, M.G., Zhang, Z., and Vance, E.R. (2007).Fe speciation in geopolymers with Si/Al molar ratio of ~2. J. Eur. Ceram. Soc., 27:2697-2703.

Rahanan, H.N. (2003). Ceramic Processing and Sintering. 2nd ed. Marcel Dekker, Inc, USA.

Schoonover, J.R., Zhang, S.L., and Johnston, C.T. (2003). Raman spectroscopy and multivariate curve resolutionof concentrated Al2O3–Na2O–H2O Solutions. J. Raman. Spectrosc., 34:404-412.

Stojanovic, B.D. (2003). Mechanochemical synthesis of ceramic powders with perovskite structure.J. Mat. Pro. Tech., 143-144:78-81.

Tsuzuki, T. and McCormick, P.G. (2000). Synthesis of Cr2O3 Nanoparticles by mechanochemical processing. Acta. Mater., 48:2795-2801.

Downloads

Published

2026-08-28

How to Cite

Eiad-ua, A., Nukaew, J., Shirai, T., & Fuji, M. (2026). MECHANO-CHEMICALFABRICATIONOF NON-FIRING CERAMIC. Suranaree Journal of Science and Technology, 20(4), 289–295. retrieved from https://ph04.tci-thaijo.org/index.php/SUJST/article/view/13911

Issue

Vol. 20 No. 4 (2013): October - December

Section

Research Article