ELECTRICAL AND MAGNETIC PROPERTIES OF MULTIFERROIC Co0.6Zn0.4Fe1.7Mn0.3O4 DOPED 0.99Bi0.47Na0.47Ba0.06Tio3-0.01Ba(Sn0.70Nb0.24)O3 CERAMICS SYNTHESIZED VIA THE SOLID-STATE COMBUSTION TECHNIQUE

Electrical and magnetic properties of CZFMO doped BNBT-BSN ceramics

Authors

  • Anupong Luangpangai Department of Physics, Faculty of Science, Naresuan University
  • Phomphon Chuai Department of Physics, Faculty of Science, Naresuan University
  • Aurawan Rittidech Department of Physics, Faculty of Science, Mahasarakham University
  • Supree Pinitsoontorn Institute of Nanomaterials Research and Innovation for Energy (IN-RIE), Khon Kaen University
  • Pongsakorn Jantaratana Department of Physics, Faculty of Science, Kasetsart University
  • Naratip Vittayakorn Advanced Materials Research Unit, Faculty of Science, King Mongkut’s Institute of Technology Ladkrabang
  • Thanya Udeye Department of Physics, Faculty of Science, Naresuan University
  • Theerachai Bongkarn Department of Physics, Faculty of Science, Naresuan University

DOI:

https://doi.org/10.55766/sujst10883

Keywords:

BNBT-BSN-xCZFMO, Dielectric, Ferroelectric, Ferromagnetic, Phase Structure

Abstract

Multiferroic (1-x)[0.99Bi0.47Na0.47Ba0.06TiO3-0.01Ba(Sn0.70Nb0.24)O3]-xCo0.6Zn0.4Fe1.7Mn0.3O4 (abbreviated as BNBT-BSN-xCZFMO) ceramics with x ranging from 0 to 0.20 were fabricated using the solid-state combustion technique. The effect of varying BNBT-BSN : CZFMO ratios on the phase structure, microstructure, electrical and magnetic properties was investigated. X-ray diffraction (XRD) analysis of pure BNBT-BSN showed a perovskite structure with rhombohedral and tetragonal phases. The doped BNBT-BSN-xCZFMO ceramics displayed coexisting rhombohedral, tetragonal, and cubic spinel phases, with the cubic spinel phase increasing when the CZFMO content increased. In addition, the XRD peaks shifted to higher angles as the CZFMO content increased, indicating a decrease in lattice parameters. The dielectric constant decreased with higher CZFMO content and higher frequencies. The pure BNBT-BSN ceramic exhibited a saturated P-E loop with a Pmax of 33.2 µC/cm2, Pr of 26.1 µC/cm2, and an Ec of 14.5 kV/cm. With increased CZFMO content, non-saturated and bloated P-E loops with lower Pmax, Pr, and Ec were observed, implying a rise in the leakage current. The addition of CZFMO induced ferromagnetic behavior in the ceramics, leading to an increase in Ms and a reduction in Hc as CZFMO content increased. The magnetoelectric coupling coefficient of BNBT-BSN-xCZFMO ceramics continuously increased with higher CZFMO content.

References

Badapanda, T., Sahoo, S., and Nayak, P. (2017). Dielectric, ferroelectric and piezoelectric study of BNT-BT solid solutions around the MPB region. Materials Science and Engineering, 178:012032. https://doi.org/10.1088/1757-899X/178/1/012032

Bongkarn, T., Chootin, S., Pinitsoontorn, S., and Maensiri, S. (2016). Excellent piezoelectric and ferroelectric properties of KNLNTS ceramics with Fe₂O₃ doping synthesized by the solid state combustion technique. Journal of Alloys and Compounds, 682:14-21. https://doi.org/10.1016/j.jallcom.2016.04.285

Cao, W.P., Li, W.L., Dai, X.F., Zhang, T.D., Sheng, J., Hou, Y.F., and Fei, W.D. (2016). Large electrocaloric response and high energy-storage properties over a broad temperature range in lead-free NBT-ST ceramics. Journal of the European Ceramic Society, 36(3):593-600. https://doi.org/10.1016/j.jeurceramsoc.2015.10.019

Chandrasekhar, M., and Kumar, P. (2015). Synthesis and characterizations of BNT-BT and BNT-BT-KNN ceramics for actuator and energy storage applications. Ceramics International, 41(4):5574-5580. https://doi.org/10.1016/j.ceramint.2014.12.136

Chitra Lekha, C.S., Kumar, A.S., Vivek, S., Venkata Saravanan, K., Anantharaman, M.R., Surendran, K.P., Nandakumar, K., and Nair, S.S. (2019). Room temperature magnetoelectric properties of lead-free alkaline niobate based particulate composites. Ceramics International, 45(7):8115-8122. https://doi.org/10.1016/j.ceramint.2019.01.089

Futakuchi, T., Kakuda, T., and Sakai, Y. (2014). Multiferroic properties of BiFeO₃-BaTiO₃ based ceramics. Journal of the Ceramic Society of Japan, 122(1426):464-468. https://doi.org/10.2109/jcersj2.122.464

Gao, R., Qin, X., Zhang, Q., Xu, Z., Wang, Z., Fu, C., Chen, G., Deng, X., and Cai, W. (2019). Enhancement of magnetoelectric properties of (1-x) Mn₀.₅Zn₀.₅Fe₂O₄-xBa₀.₈₅Sr₀.₁₅Ti₀.₉Hf₀.₁O₃ composite ceramics. Journal of Alloys and Compounds, 795:501-512. https://doi.org/10.1016/j.jallcom.2019.05.013

Gupta, A., Huang, A., Shannigrahi, S., and Chatterjee, R. (2011). Improved magnetoelectric coupling in Mn and Zn doped CoFe₂O₄-PbZr₀.₅₂Ti₀.₄₈O₃ particulate composite. Applied Physics Letters, 98:112901.

Jia, Y., Fan, H., Wang, H., Yadav, A. K., Yan, B., Li, M., Quan, Q., Dong, G., Wang, W., and Li, Q. (2021). Large electrostrain and high energy-storage of (1-x)[0.94(Bi₀.₅Na₀.₅)TiO₃-0.06BaTiO₃]-xBa(Sn₀.₇₀Nb₀.₂₄)O₃ lead-free ceramics. Ceramics International, 47(13):18487-18496. https://doi.org/10.1016/j.ceramint.2021.03.172

Jiang, J., and Ai, L.H. (2010). Synthesis and characterization of Fe-Co binary ferrospinel nanospheres via one-step nonaqueous solution pathway. Materials Letters, 64(8):945-947. https://doi.org/10.1016/j.matlet.2010.01.067

Kornphom, C., Saenkam, K., Jantaratana, P., Pinitsoontorn, S., and Bongkarn, T. (2023). Investigations on the multiferroic properties of lead free BNT-BCTS:MFO ceramic composites fabricated by the solid-state combustion technique. JOM, 75(7):2669-2683. https://doi.org/10.1007/s11837-023-05835-1

Lee, M.H., Kim, D.J., Park, J.S., Kim, S.W., Song, T.K., Kim, M.H., Kim, W.J., Do, D., and Jeong, I.K. (2015). High-performance lead-free piezoceramics with high Curie temperatures. Advanced Materials, 27(43):6976-6982. https://doi.org/10.1002/adma.201502424

Li, J.F., Wang, K., Zhu, F.Y., Cheng, L.Q., Yao, F.Z., and Green, D.J. (2013). (K,Na)NbO₃-based lead-free piezoceramics: Fundamental aspects, processing technologies, and remaining challenges. Journal of the American Ceramic Society, 96(12):3677-3696. https://doi.org/10.1111/jace.12715

Li, L., Hao, J., Xu, Z., Li, W., and Chu, R. (2016). 0.46% unipolar strain in lead-free BNT-BT system modified with Al and Sb. Materials Letters, 184:152-156. https://doi.org/10.1016/j.matlet.2016.07.150

Luangpangai, A., Jirattitikarn, T., Somsri, W., Rittidech, A., Prasertpalichat, S., and Bongkarn, T. (2024). Enhanced dielectric and ferroelectric properties near the morphotropic phase boundary in BNBT-BSN ceramics prepared by the solid-state combustion technique. Scientific Reports, 14(1):30268. https://doi.org/10.1038/s41598-024-81758-4

Mane, S.M., Tirmali, P.M., Ranjit, B., Khan, M., Khan, N., Tarale, A.N., and Kulkarni, S.B. (2018). Studies on magnetocapacitance, dielectric, ferroelectric, and magnetic properties of microwave sintered (1-x)(Ba₀.₈Sr₀.₂TiO₃)-x(Co₀.₉Ni₀.₁Fe₂O₄) multiferroic composite. Solid State Sciences, 81:43-50. https://doi.org/10.1016/j.solidstatesciences.2018.05.004

Nagata, H., Shinya, T., Hiruma, Y., Takenaka, T., Sakaguchi, I., and Haneda, H. (2006). Piezoelectric properties of bismuth sodium titanate ceramics. Ceramic Transactions, 167:213-221. https://doi.org/10.1002/9781118408186.ch20

Nanda, D., Kumar, P., Samanta, B., Sahu, R., and Singh, A. (2019). Structural, dielectric, ferroelectric and magnetic properties of (BNT-BT)-NCZF composites synthesized by a microwave-assisted solid-state reaction route. Journal of Electronic Materials, 48(8):5039-5047. https://doi.org/10.1007/s11664-019-07304-5

Parija, B., Badapanda, T., Rout, S.K., Cavalcante, L. S., Panigrahi, S., and Longo, E. (2013). Morphotropic phase boundary and electrical properties of 1-x[Bi₀.₅Na₀.₅]TiO₃-xBa[Zr₀.₂₅Ti₀.₇₅]O₃ lead-free piezoelectric ceramics. Ceramics International, 39(5):4877-4886. https://doi.org/10.1016/j.ceramint.2012.11.080

Rani, R., Kumar, P., Singh, S., Juneja, J.K., and Prakash, C. (2017). Improvement in magnetoelectric and other physical properties of BSZT-NZF composites by microwave sintering. Journal of Alloys and Compounds, 690:716-719. https://doi.org/10.1016/j.jallcom.2016.08.119

Priya, A.S., Banu, I.B.S., and Chavali, M. (2015). Influence of (La, Cu) doping on the room temperature multiferroic properties of BiFeO₃ ceramics. Arabian Journal of Science and Engineering, 40(7):2079-2084. https://doi.org/10.1007/s13369-015-1668-z

Singh, H., Kumar, A., and Yadav, K.L. (2011). Structural, dielectric, magnetic, magnetodielectric and impedance spectroscopic studies of multiferroic BiFeO₃-BaTiO₃ ceramics. Materials Science and Engineering B, 176(7):540-547. https://doi.org/10.1016/j.mseb.2011.01.010

Singh, M., Singh, J., Kumar, M., and Kumar, S. (2020). Investigations on multiferroic properties of lead free (1-x)BCZT-xCZFMO based particulate ceramic composites. Solid State Sciences, 108:106380. https://doi.org/10.1016/j.solidstatesciences.2020.106380

Sinkruason, T., Luangpangai, A., Charoenthai, N., Rittidech, A., Pulphol, P., Vittayakorn, N., and Bongkarn, T. (2023). Phase formation and electrical properties of SBNLT ceramics prepared via combustion technique. Materials Science and Technology. 39(18):3065-3075. doi:10.1080/02670836.2023.2238415

Swain, S., Kar, S.K., and Kumar, P. (2015). Dielectric, optical, piezoelectric and ferroelectric studies of NBT-BT ceramics near MPB. Ceramics International, 41(9):10710-10717. https://doi.org/10.1016/j.ceramint.2015.05.005

Thatawong, B., Bhupaijit, P., Lamyai, Y., Vittayakorn, N., and Bongkarn, T. (2022). Dielectric and piezoelectric properties near the morphotropic phase boundary for 0.94BNT-0.06BT ceramics synthesized by the solid-state combustion technique. Ferroelectrics, 586(1):199-212. https://doi.org/10.1080/00150193.2021.2014271

Thawong, P., Punlek, N., Pinitsoontorn, S., and Bongkarn, T. (2019). Effect of the firing temperature on the phase formation, dielectric and ferromagnetic properties of CZFMO ceramics fabricated by the solid-state combustion technique. Ferroelectrics, 552(1):10-22. https://doi.org/10.1080/00150193.2019.1653078

Venkata Ramana, E., Graça, M.P.F., Monteiro, J., Mendiratta, S.K., and Valente, M.A. (2012). Improved magnetoelectric effect in modified (Na0.5Bi0.5)TiO3-BaTiO3-CoFe2O4 lead-free multiferroic composites. In Proceedings of ISAF-ECAPD-PFM 2012 (pp. 1-4). https://doi.org/10.1109/ISAF.2012.6297834

Vopson, M.M., Fetisov, Y.K., Caruntu, G., and Srinivasan, G. (2017). Measurement techniques of the magneto-electric coupling in multiferroics. Materials, 10(8):963. https://doi.org/10.3390/ma10080963

Wan, Y., Li, Y., Li, Q., Zhou, W., Zheng, Q., Wu, X., Xu, C., Zhu, B., and Lin, D. (2014). Microstructure, ferroelectric, piezoelectric, and ferromagnetic properties of Sc-modified BiFeO₃-BaTiO₃ multiferroic ceramics with MnO₂ addition. Journal of the American Ceramic Society, 97(6):1809-1818. https://doi.org/10.1111/jace.12827

Wang, C., and Shi, P. (2023). Bi₀.₂Sr₀.₇TiO₃-doped Bi₀.₅Na₀.₅TiO₃-based lead‑free ceramics with good energy storage properties. Journal of Materials Science: Materials in Electronics, 34:1774.

Wu, M.S., Tian, Z.M., Yuan, S.L., Duan, H.N., and Qiu, Y. (2012). Dielectric behavior and AC conductivity in Aurivillius Bi₄Ti₃O₁₂ doped by antiferromagnetic BiFeO₃. Physics Letters A, 376(28-29):2062-2066. https://doi.org/10.1016/j.physleta.2012.01.012

Xiao, S.H., Luo, K., and Zhang, L. (2010). The structural and magnetic properties of cobalt ferrite nanoparticles formed in situ in silica matrix. Materials Chemistry and Physics, 123(2-3):385-389. https://doi.org/10.1016/j.matchemphys.2010.04.026

Zawar, S., Atiq, S., Tabasum, M., Riaz, S., and Naseem, S. (2019). Highly stable dielectric frequency response of chemically synthesized Mn-substituted ZnFe₂O₄. Journal of the Saudi Chemical Society, 23(4):417-426. https://doi.org/10.1016/j.jscs.2018.06.010

Zhang, H., Zhou, J., Shen, J., Yang, X., Wu, C., Han, K., Zhao, Z., and Chen, W. (2017). Enhanced piezoelectric property and promoted depolarization temperature in Fe-doped Bi₁/₂(Na₀.₈K₀.₂)₁/₂TiO₃ lead-free ceramics. Ceramics International, 43(18):16395-16402. https://doi.org/10.1016/j.ceramint.2017.09.015

Zhang, R.F., Deng, C.Y., Ren, L., Li, Z., and Zhou, J.P. (2013). Dielectric, ferromagnetic and magnetoelectric properties of BaTiO₃-Ni₀.₇Zn₀.₃Fe₂O₄ composite ceramics. Materials Research Bulletin, 48(10):4100-4104. https://doi.org/10.1016/j.materresbull.2013.06.026

Zou, M., Fan, H., Chen, L., and Yang, W. (2010). Microstructure and electrical properties of (1-x)[0.82Bi₀.₅Na₀.₅TiO₃-0.18Bi₀.₅K₀.₅TiO₃]-xBiFeO₃ lead-free piezoelectric ceramics. Journal of Alloys and Compounds, 495(1):280-283. https://doi.org/10.1016/j.jallcom.2010.02.025

Downloads

Published

2025-08-19

How to Cite

Luangpangai, A., Chuai, P., Rittidech, A., Pinitsoontorn, S., Jantaratana, P., Vittayakorn, N., Udeye, T., & Bongkarn, T. (2025). ELECTRICAL AND MAGNETIC PROPERTIES OF MULTIFERROIC Co0.6Zn0.4Fe1.7Mn0.3O4 DOPED 0.99Bi0.47Na0.47Ba0.06Tio3-0.01Ba(Sn0.70Nb0.24)O3 CERAMICS SYNTHESIZED VIA THE SOLID-STATE COMBUSTION TECHNIQUE: Electrical and magnetic properties of CZFMO doped BNBT-BSN ceramics. Suranaree Journal of Science and Technology, 32(4), 030326(1–14). https://doi.org/10.55766/sujst10883

Issue

Section

Research Article

Categories